RK3588 Android12 广和通L716 4G模块调试记录

2023-09-07 13:08

短信预约 -IT技能 免费直播动态提醒

调试前先找模块厂获取相关资料

Kernel修改：

可用RK的参考配置来控制，把原理图对应角位配置上就行。

rk_modem: rk-modem {compatible="4g-modem-platdata";pinctrl-names = "default";pinctrl-0 = <<e_vbat <e_power_en <e_reset>;4G,vbat-gpio = <&gpio4 RK_PD0 GPIO_ACTIVE_HIGH>;4G,power-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>;4G,reset-gpio = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;status = "okay";};

添加模块VID,PID

kernel-5.10：--- a/drivers/usb/serial/option.c+++ b/drivers/usb/serial/option.c@@ -97,6 +97,18 @@ static void option_instat_callback(struct urb *urb); #define YISO_VENDOR_ID                         0x0EAB #define YISO_PRODUCT_U893                      0xC893 ++#define FIBOCOM_VENDOR_ID                      0x2cb7+#define FIBOCOM_PRODUCT_L71X           0x0001++#define FIBOCOM_USB_VENDOR_AND_INTERFACE_INFO(vend, cl, sc, pr) \+.match_flags = USB_DEVICE_ID_MATCH_INT_INFO \+| USB_DEVICE_ID_MATCH_VENDOR, \+.idVendor = (vend), \+.bInterfaceClass = (cl), \+.bInterfaceSubClass = (sc), \+.bInterfaceProtocol = (pr)+ @@ -2188,6 +2205,16 @@ static int option_probe(struct usb_serial *serial,        if (iface_desc->bInterfaceClass == USB_CLASS_MASS_STORAGE)                return -ENODEV; +       if(serial->dev->descriptor.idVendor == FIBOCOM_VENDOR_ID &&+               serial->dev->descriptor.idProduct == FIBOCOM_PRODUCT_L71X &&+               serial->interface->cur_altsetting->desc.bInterfaceClass == 0x7)+               return -ENODEV;++       if(serial->dev->descriptor.idVendor == ZTE_VENDOR_ID &&+               serial->dev->descriptor.idProduct == 0x0579 &&+               serial->interface->cur_altsetting->desc.bInterfaceClass == 0x6)+               return -ENODEV;+                        if ((dev->driver_info->flags & FLAG_WLAN) != 0)                        strcpy(net->name, "wlan%d");

以上修改完成后编译烧录进机器查看是否生成对应设备

console:/ # lsusb      Bus 006 Device 003: ID 2cb7:0001console:/ # ifconfig  -ausb0      Link encap:Ethernet  HWaddr 34:4b:50:00:00:00  Driver cdc_ether          BROADCAST MULTICAST  MTU:1500  Metric:1          RX packets:0 errors:0 dropped:0 overruns:0 frame:0          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0          collisions:0 txqueuelen:1000          RX bytes:0 TX bytes:0console:/ # ls /dev/ttyUSB*                        /dev/ttyUSB0  /dev/ttyUSB1  /dev/ttyUSB2  /dev/ttyUSB3

问题排查：

如未生成对应节点先排查供电是否正常。

在排查主控对应USB phy节点是否打开

模块需保证 VBUS 信号连接到 5V 供电，若此信号悬空，USB 口无法正常枚举

Android修改：

1.启动ril进程

hardware/ril--- a/rild/rild.rc+++ b/rild/rild.rc@@ -1,5 +1,6 @@-service vendor.ril-daemon /vendor/bin/hw/rild+service ril-daemon /vendor/bin/hw/rild -l /vendor/lib64/libreference-ril-l716.so     class main-    user radio-    group radio cache inet misc audio log readproc wakelock-    capabilities BLOCK_SUSPEND NET_ADMIN NET_RAW+    socket rild stream 660 root radio+    socket rild-debug stream 660 radio system+    user root+    group radio cache inet misc audio sdcard_rw log启动rild进程加载对应ril库-l 指定 RIL 库加载路径

2.打开系统4G服务

device/rockchip/common/BoardConfig.mkBOARD_HAS_RK_4G_MODEM ?= true

3.打开BOARD_HAS_RK_4G_MODEM选项后会有一些报错，添加如下补丁：（如打开宏没有报错不用添加下面补丁，rk3568可以直接编译，目前发现rk3588 android12会报错）

/vendor/rockchip/common：--- a/phone/phone.mk+++ b/phone/phone.mk@@ -26,8 +26,8 @@ PRODUCT_PACKAGES += \     chat  PRODUCT_PROPERTY_OVERRIDES +=ro.boot.noril=false-else-PRODUCT_PROPERTY_OVERRIDES +=ro.boot.noril=true+# else+# PRODUCT_PROPERTY_OVERRIDES +=ro.boot.noril=true endif

/device/rockchip/common：--- a/modules/4g_modem.mk+++ b/modules/4g_modem.mk@@ -38,8 +38,8 @@ PRODUCT_PROPERTY_OVERRIDES += \     vendor.rild.libpath=/vendor/lib64/librk-ril.so  PRODUCT_COPY_FILES += \-    $(LOCAL_PATH)/4g_modem/bin64/dhcpcd:$(TARGET_COPY_OUT_VENDOR)/bin/dhcpcd \-    $(LOCAL_PATH)/4g_modem/lib64/librk-ril.so:$(TARGET_COPY_OUT_VENDOR)/lib64/librk-ril.so+    $(LOCAL_PATH)/../4g_modem/bin64/dhcpcd:$(TARGET_COPY_OUT_VENDOR)/bin/dhcpcd \+    $(LOCAL_PATH)/../4g_modem/lib64/librk-ril.so:$(TARGET_COPY_OUT_VENDOR)/lib64/librk-ril.so

hardware/interfaces：--- a/compatibility_matrices/compatibility_matrix.6.xml+++ b/compatibility_matrices/compatibility_matrix.6.xml@@ -434,6 +434,11 @@                   android.hardware.radio+        1.1+        1.2+        1.3+        1.4+        1.5         1.6                      IRadio@@ -450,11 +455,20 @@             slot1              +    +       android.hardware.radio.deprecated+        1.0+        +        IOemHook+        slot1+        +                      android.hardware.radio.config         +        1.0         1.1                      IRadioConfig

4.添加模块厂提供ril库编译并指定ril库路径

所需文件：libreference-ril-l716.so

ght_ril_config.ini

将文件拷贝到/device/rockchip/common/lib64目录

添加如下代码拷贝到系统

/device/rockchip/common：--- a/modules/4g_modem.mk+++ b/modules/4g_modem.mk@@ -35,11 +35,12 @@ DEVICE_MANIFEST_FILE += device/rockchip/common/4g_modem/manifest.xml  ifeq ($(strip $(TARGET_ARCH)), arm64) PRODUCT_PROPERTY_OVERRIDES += \-    vendor.rild.libpath=/vendor/lib64/librk-ril.so+    vendor.rild.libpath=/vendor/lib64/libreference-ril-l716.so  PRODUCT_COPY_FILES += \-    $(LOCAL_PATH)/4g_modem/bin64/dhcpcd:$(TARGET_COPY_OUT_VENDOR)/bin/dhcpcd \-    $(LOCAL_PATH)/4g_modem/lib64/librk-ril.so:$(TARGET_COPY_OUT_VENDOR)/lib64/librk-ril.so+    $(LOCAL_PATH)/../4g_modem/bin64/dhcpcd:$(TARGET_COPY_OUT_VENDOR)/bin/dhcpcd \+    $(LOCAL_PATH)/../4g_modem/lib64/libreference-ril-l716.so:$(TARGET_COPY_OUT_VENDOR)/lib64/libreference-ril-l716.so \+    $(LOCAL_PATH)/../4g_modem/lib64/ght_ril_config.ini:system/etc/ght_ril_config.ini else PRODUCT_PROPERTY_OVERRIDES += \     vendor.rild.libpath=/vendor/lib/librk-ril.so

5.修改模块所需prop属性

device/rockchip/rk3588：--- a/device.mk+++ b/device.mk@@ -82,6 +82,9 @@ PRODUCT_PROPERTY_OVERRIDES += \                 ro.ril.ecclist=112,911 \                 ro.opengles.version=196610 \                 wifi.interface=wlan0 \+                rild.libargs=-d /dev/ttyUSB2 \+                ril.fibocom.dialmode=1 \+                ril.fibocom.NetifName=usb0 \参数说明：rild.libargs  AT指令端口，可询问模块厂或向端口发送AT指令可得知，一般只ttyUSB1 ttyUSB2ril.fibocom.dialmode   拨号模式    / 0 ： ppp 拨号， 1 ： ECM 拨号 //推荐使用ECMril.fibocom.NetifName   自定义拨号网卡，根据实际生成网卡填写

6.添加信号图标，4G图标

/device/rockchip/common：--- a/overlay_wifi_only/frameworks/base/core/res/res/values/config.xml+++ b/overlay_wifi_only/frameworks/base/core/res/res/values/config.xml@@ -22,5 +22,5 @@          If true, this means that the device supports data connectivity through          the telephony network.          This can be overridden to false for devices that support voice and/or sms . -->-    false+    true /device/rockchip/rk3588：--- a/overlay/frameworks/base/core/res/res/values/config.xml+++ b/overlay/frameworks/base/core/res/res/values/config.xml@@ -31,6 +31,14 @@                   "wifi,1,1,2,-1,true"+        "mobile,0,0,0,-1,true"+        "mobile_mms,2,0,2,60000,false"+        "mobile_supl,3,0,2,60000,true"+        "mobile_dun,4,0,2,60000,true"+        "mobile_hipri,5,0,3,60000,true"+        "mobile_fota,10,0,2,60000,true"+        "mobile_ims,11,0,2,60000,true"+        "mobile_cbs,12,0,2,60000,true"             "bluetooth,7,7,0,-1,true"         "ethernet,9,9,9,-1,true"

7.编译Android烧录

8.系统界面显示

FAQ：如有问题按如下方式排查：

9.编译完成后查看系统属性是否已经设置成功

console:/ # getprop | grep ril                     [init.svc.ril-daemon]: [running][init.svc_debug_pid.ril-daemon]: [505][ril.currentapntype]: [default][ril.fibocom.NetifName]: [usb0][ril.fibocom.dialmode]: [1][ril.fibocom.version]: [Fibocom_RIL_V12X.06.V1.0.7][ril.function.dataonly]: [1][rild.libargs]: [-d][ro.boot.noril]: [false][ro.boottime.ril-daemon]: [5861295027][ro.ril.ecclist]: [112,911][vendor.rild.libpath]: [/vendor/lib64/libreference-ril-l716.so]

9.1查看rild进程是否启动

console:/ # ps -ef | grep rildroot           505     1 0 10:03:39 ?     00:00:00 rild -l /vendor/lib64/libreference-ril-l716.soroot         19667  2210 3 10:43:59 ttyFIQ0 00:00:00 grep rild

9.2AT指令排查

输入AT指令到对应端口号查看是否检测到SIM卡开两个adb端口，一个执行echo,一个执行catecho -e "AT+CPIN?" > /dev/ttyUSB2cat /dev/ttyUSB2CPIN: READY查看信号强度：echo -e "AT+CSQ\r\n" >/dev/ttyUSB2cat /dev/ttyUSB2+CSQ: 14,99

9.3 ifconfig -a查看网卡是否启动，如未启动，手动执行ifoconfig usb0 up，或者进入设置--网络选项